Everyone has got his or her own conception on the subject of How to Install a Bathtub.
Setting up a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably tough job. If the old tub is readily accessible, the task can relocate immediately; if you need to open a wall to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the new one. See to it you have actually qualified on your own for the work as well as are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Chances are you might need a professional plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your restroom if you have actually currently purchased a brand-new tub and also don't need to transform the plan of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome as a result of the restricted gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before moving on to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washing machines are in place in between the faucet and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type should be connected to the faucet ends initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Making use of the two wooden boards under its feet, put the bathtub in the called for position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and changing the feet on the bathtub up until the level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub must wait till the bath tub has actually been made use of at least once as this will settle it into its final setting.
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that post about Installing A Bathtub when surfing around the search engines. Kindly take a moment to share this write-up if you appreciated it. Kudos for your time. Please stop by our blog back soon.
Click Here To Find Out More